problem tråløst open suse

[Raven80]

hei.

har lagt inn denne http://en.opensuse.org/Atheros_madwifi

noen som kan hjelpe meg med dette?

Power Management and madwifi

Add this file to the power management script directory to ensure that wireless works after suspending. In openSUSE 10.3, it's in the /etc/pm/sleep.d directory, and in openSUSE 10.2, it's in the /etc/pm/power directory. You can call it 60madwifi. You'll also need to make it executable. It's run by root, so be careful about adding things to it.

#!/bin/bash
case $1 in
hibernate)
/etc/init.d/network stop
/sbin/modprobe -r ath_pci
;;
suspend)
/etc/init.d/network stop
/sbin/modprobe -r ath_pci
;;
thaw)
/sbin/modprobe ath_pci
/etc/init.d/network start
;;
resume)
/sbin/modprobe ath_pci
/etc/init.d/network start
;;
*) echo "madwifi power management script called incorrectly."
;;
esac

[omaha]

Sikker på at du har rett driver til kortet ditt?

Kode: Merk alt

lsusb

Kode: Merk alt

lspci

[Raven80]

nei, er ikke sikker..

dette fikk jeg opp:

steffen@linux-psgr:~> lsusb
Bus 003 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
steffen@linux-psgr:~> lspci
bash: lspci: command not found
steffen@linux-psgr:~>

[Raven80]

hmm, noen vet?

[unbob]

Du må nok kjøre lspci som root.

[Raven80]

dette fikk jeg opp:

linux-psgr:~ # lspci
00:00.0 Host bridge: VIA Technologies, Inc. P4M900 Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. P4M900 Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. P4M900 Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. P4M900 Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. P4M900 Host Bridge
00:00.5 PIC: VIA Technologies, Inc. P4M900 I/O APIC Interrupt Controller
00:00.6 Host bridge: VIA Technologies, Inc. P4M900 Security Device
00:00.7 Host bridge: VIA Technologies, Inc. P4M900 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:02.0 PCI bridge: VIA Technologies, Inc. P4M900 PCI to PCI Bridge Controller (rev 80)
00:03.0 PCI bridge: VIA Technologies, Inc. P4M900 PCI to PCI Bridge Controller (rev 80)
00:0f.0 IDE interface: VIA Technologies, Inc. VT8237A SATA 2-Port Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 07)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev a0)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev a0)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237A PCI to ISA Bridge
00:11.7 Host bridge: VIA Technologies, Inc. VT8251 Ultra VLINK Controller
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c)
00:13.0 PCI bridge: VIA Technologies, Inc. VT8237A Host Bridge
00:13.1 PCI bridge: VIA Technologies, Inc. VT8237A PCI to PCI Bridge
01:00.0 VGA compatible controller: VIA Technologies, Inc. Chrome9 HC IGP (rev 01)
04:01.0 Audio device: VIA Technologies, Inc. VIA High Definition Audio Controller (rev 10)
05:01.0 Ethernet controller: Atheros Communications, Inc. AR2413 802.11bg NIC (rev 01)

[unbob]

Beklager men leste først nå gjennom hele tråden...

Hva er det som egentlig er problemet? Virker ikke det trådløse kortet når maskinen kommer tilbake fra hvilemodus?

[Raven80]

det virker ikke i det heletatt.. det står det mangler noe.. hva kan det være?

[unbob]

Spør du meg, så spør jeg deg.
Du må nesten lime inn feilmeldingen her og fortelle hva du gjør for å få denne feilmeldingen.

I tillegg til feilmeldingen; kan du lime inn output fra følgende:

Kode: Merk alt

ifconfig -a
iwconfig
modprobe -l | grep ath_pci
lsmod | grep ath_pci


(de må utføres som root)

[Raven80]

hei, får ikke noe feilmelding, har ikke noe tråløstnett.
men vis jeg går på YaST --> nettverksenheter --> nettverkskort dær ligger det
Ethernet-nettverkskort kan dette være tråløst?

Ethernet-nettverkskort (ikke tilkoblet)
BusID : 0000:05:01.0
Klarte ikke å sette opp nettverkskortet fordi kjernemodulen mangler

Passord:
laptop-PC:~ # ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:14:0B:0A:B0:D0
inet addr:10.0.0.5 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::214:bff:fe0a:b0d0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:25546 errors:0 dropped:0 overruns:0 frame:0
TX packets:21130 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:22833459 (21.7 Mb) TX bytes:2815524 (2.6 Mb)
Interrupt:21 Base address:0x4800

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1318 errors:0 dropped:0 overruns:0 frame:0
TX packets:1318 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:79476 (77.6 Kb) TX bytes:79476 (77.6 Kb)

laptop-PC:~ # iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

laptop-PC:~ # modprobe -l | grep ath_pci
laptop-PC:~ # lsmod | grep ath_pci
laptop-PC:~ #

[unbob]

Nei det er nok ikke ett trådløst kort.

Men du "mangler" egentlig alt som skulle tilsi at det trådløse kortet skulle virke.
Har du gjort det som står i lenken du limte inn i din første post?
http://en.opensuse.org/Atheros_madwifi

[Raven80]

jeg har installert noe men ikke noe mer, skal sikkert redigere noe tekst, men skjønner ikke helt

[unbob]

Gjør det som står her (Installation using Zypper (Command line) ), og lim inn eventuelle feilmeldinger her.

[Raven80]

hmm, skal dette limes inn i treminalen?

Installation using Zypper (Command line)

zypper -v sa http://madwifi.org/suse/`python -c "import platform;print platform.dist()[1]"` madwifi
zypper install madwifi madwifi-kmp-`uname -r | awk -F- '{print $3}'`

[unbob]

Skal limes inn i terminalen, ja.